Научные статьиM.H.Sayidova, S.U.Pulatova2025
TYPES, SOURCES, AND ROLES OF VITAMINS IN THE HUMAN BODY
THEIRSTRUCTURE ANDPROPERTIES · Nurullayev R.T. · Saydullayev A.Sh.
Международный мультидисциплинарный журнал исследований и разработок · 12 · 2019
Аннотация
This study investigates the deformation behavior of various steels and alloys under high-temperature and isothermal conditions. The effects of deformation rate, temperature, and initial microstructure on the mechanical properties and microstructural changes during deformation are analyzed. The use of isothermal conditions allows for improved control over deformation processes, leading to enhanced product quality and material performance. Experimental methods include tensile testing at various temperatures and deformation rates, as well as microstructural analysis. The results provide insights into optimizing thermomechanical processing regimes for bettermechanical properties and efficiency inmetal forming. Key words: Isothermal deformation, steel microstructure, mechanical properties, high- temperaturetesting, thermomechanical processing, tensiletesting, alloy deformation Tosolve theassigned tasks, technically pure iron, A40G, U8A, and U12A steels wereselected. The choice of these materials is justified by the following reasons: firstly, they cover the entire "steel" section of the iron-carbon phase diagram; secondly, these industrially produced materials have a similar composition in terms of main alloying elements and differ primarily in their carbon content (see Table 1.1), which allows for determining the influence of cementite content on the plasticityof steels. The materials used for the research were wires hot-rolled in the plastic state. The chemical compositionof thematerials under investigation is presented in Table 2.1. Table1.1 Chemical Composition oftheMaterials UnderInvestigation № Steel grades C Mn Si S P Cu t/r 1. Technically pure iron 0,04 0,30 0,35 0,01-0,02 - 0,28 2. Steel grade A40G 0,40 0,80 0,28 0,41 0,016 - 3. Steel grade U8A 0,79 0,35 0.2 0,03 - - 4. Steel gradeU12A 1.17 0,36 0,18 - - - The microstructure of the steels in the initial sample state was studied in both the longitudinal and cross-sections ofthe wires. 114 INTERNATIONAL MULTIDISCIPLINARY JOURNAL FOR RESEARCH & DEVELOPMENT SJIF 2019:5.2222020:5.5522021: 5.6372022:5.479 2023:6.563 2024: 7,805 eISSN:2394-6334 https://www.ijmrd.in/index.php/imjrd Volume 12,issue06(2025) The microstructure of the steels in the initial sample state is shown in Figures 1.1a, b, and c. A40G steel has a ferrite–lamellar pearlite structure, U8A steel exhibits a eutectoid (0.8% carbon) pearlitic structure in the initial state, while U12A steel has a eutectoid structure consisting of pearliteand cementite. To study the effect of the initial state on high-temperature plasticity, thermal treatment (quenching followed byhigh-temperature tempering) and priorhot deformation were applied. a)Commercially pureiron; b) A40Gsteel; c)U8A steel; d)U12A steel, 500×magnification Figure1.1.Microstructure of steels inthe initial condition: §2.2.Methodology of Mechanical Testing byUpsetting Tensile tests at high temperatures were carried out using a universal testing machine of the brand Instron, model TT1114, within a temperature range of 400 to 1000 °C and deformation speeds ranging from 0.05 to 500 mm/min. The samples were prepared according to GOST 1495- 73, with a gauge section diameter of 5 mm and a length of 25 mm. Heating of the samples to the test temperatures was conducted in a three-zone resistance furnace, ensuring a temperature deviation ofnomore than ±3 °Cover alengthof 300mm. To ensure uniform heating and temperature stabilization, the samples were held in the furnace for20minutes priorto deformation at the specified temperature. 115 INTERNATIONAL MULTIDISCIPLINARY JOURNAL FOR RESEARCH & DEVELOPMENT SJIF 2019:5.2222020:5.5522021: 5.6372022:5.479 2023:6.563 2024: 7,805 eISSN:2394-6334 https://www.ijmrd.in/index.php/imjrd Volume 12,issue06(2025) To reduce oxidation of the samples at high temperatures (t > 600–700 °C), a protective enamel coating such as EVT13 or EVT24 was applied. This coating was rubbed onto the working section of thesamplepriorto heating. Two groups of samples were used in the experiments. The first group consisted of small samples with a diameter of 10 mm and a height of 15 mm. These samples were deformed on a U10 universal testing machinewith astrain (ε) ranging from30%to 80%. These samples were used in the development of a method for obtaining an ultrafine- grained (UFG) structure, with the aim of systematically studying structural changes and mechanicalproperties during theprocess. Preparationof Samples forMechanicalTesting Another group of larger samples, with dimensions of 30 mm in diameter and 60 mm in height, was subjected to isothermal upsetting in a die block using a modernized RN-100A hydraulic press with a 100-ton capacity. Heating of the samples was carried out by an inductor connected to a PST-100 converter. The deformation rate was 5·10⁻³ s⁻¹, and the degree of deformation was at least 60%. From the large preforms (blanks) obtained after upsetting, standard specimens for tensilemechanical testing (Figure 2.3)and samples
Доказательный фрагмент
«This study investigates the deformation behavior of various steels and alloys under high-temperature and isothermal conditions.»
Образец извлечения
Демо-превьюThis study investigates the deformation behavior of various steels and alloys under high-temperature and isothermal conditions. Полный текст публикации CiteX не хранит — доступ к первоисточнику открывается по DOI согласно лицензии издателя и выбранному плану.
- Цитирований
- 0
- Тип
- Журнал
- Страна
- Узбекистан
- Ключевые слова
- Isothermal deformation, steel microstructure, mechanical properties, high-
Смежные источники
Общество и инновацииKhosiyat MAMATKULOVA2024
Академические исследования в современной наукеKhudaiberdiyeva Arafat Israilovna, Ph.D Professor hudayberdiyevaarofat@gmail.com +12026
Научные статьиI.B.Yangiboyev, E.X.Berdanov +22025