Научные статьиM.H.Sayidova, S.U.Pulatova2025
ANALYSIS OF DESIGNS AND CONDITIONS OF APPLICATION OF CARBIDE DRILLS FOR EXTREME OPERATING CONDITIONS
SCIENCE SHINE · Narziyeva Shahrizoda Shokirjon qizi
Свет науки · 1 · 2025
Аннотация
The share of drilling operations in the total volume of mechanical processing reaches 30...40%. Therefore, the successful implementation of repair and rescue operations in emergency situations largely depends on the reliable execution of a number of drilling operations, which are mainly determined by the operational reliability of the axial tool used. I will discuss this in this article. Keywords: Drilling, carbide drills, operating conditions, deep-hole drills, strength and hardness. Carrying out drilling operations during processing of metal and concrete structures, in conditions close to field conditions, is characterized by the use of technological equipment with reduced rigidity, since in such conditions there is no possibility of using a stable stationary technological system. Under such operating conditions, standard drills do not have a stable position that ensures a continuous cutting process, and the cutting edges of the tools chip long before the planned service life. It is important to take into account that concrete structures reinforced with metal belong to the class of difficult-to-process materials. A summary of many years of experience in the operation of axial tools in extreme conditions shows that the greatest difficulties are associated with the processing of holes with a diameter of 20... 35 mm. Holes with a diameter of 20-35 mm are most widely used in machines and mechanisms of land vehicles, as well as in railway transport and in the connection of railway rails. Therefore, this range of holes is the most common and usually requires the use of fairly expensive carbide tools and special equipment. When processing holes in this range, the cutting power, depending on the material being processed, reaches 1.5... 2.0 kW, and the specific cutting work is 15... 25 J/mm3. In stationary processing conditions, this requires fairly powerful and heavy equipment, which is unacceptable when working in emergency situations. In such conditions, portable equipment based on the RSM-1M model machines is usually used. However, this type of equipment has low technological rigidity. For this reason, vibrations and transverse oscillations of the tool occur during drilling, and the processed holes have a pronounced facet and diameter difference. Therefore, the 264 SCIENCE SHINE INTERNATIONAL SCIENTIFIC JOURNAL Issue 10(45), Volume 1 | ISSN 3030-377X | 20.05.2025 technological range of drilling tools is significantly limited by the economic feasibility of using the selected or developed drill design. The analysis of cutting patterns that meet field operating conditions must be carried out under the following restrictions: 1. Performing a drilling operation with a reliability of no less than P = 0.95. 2. Technological adjustment should be carried out at low rigidity of the technological equipment. 3. The cutting part of the tool must ensure productive processing modes. 4. Operation of the tool without coolants. Within the above-mentioned limitations, first of all, the material of the cutting part of the drilling tool should be determined, provided that the design of the drill should have an increased degree of reliability. Experience in operating the tool in factory conditions shows that tool materials such as superhard (diamond, elbor, corundum), ceramic alloys - cermets find limited application in blade processing due to the strength properties of the materials being processed. Table 1.1 shows the physical and mechanical properties of some tool materials. Table 1.1 shows the classification of tool materials according to their strength and hardness. Table 1.1 Properties of High Hard Mineral Silinite Cubic Diamonds materials speed alloys ceramics boron steels nitride Density 8-9 8-15 3,6-4,0 3,4-3,8 3,5 3,5 g/sm3 Hardness H 700-800 850-1400 1400- 900-3000 8000- 9000- 2000 9000 10000 Compressive 2500- 3500- 1300- 3000 1500- 2000- strength 4000 5900 3000 2000 6000 N/mm2 Bending 2000- 1000- 250-600 300-700 300 300-400 strength 6000 3400 N/mm2 Heat 600-700 800-1000 1200 - 1400- 700-900 resistance, 1500 deg. Coefficient 9-12 3-7,5 2,5-9,0 2,75-3,0 - 1,5-1,9 of linear expansion, deg.-1x10-6 265 SCIENCE SHINE INTERNATIONAL SCIENTIFIC JOURNAL Issue 10(45), Volume 1 | ISSN 3030-377X | 20.05.2025 Young's 25-30 47-65 30-45 - - 90-100 modulus N/mm2 Analysis of the physical and mechanical properties of the presented cutting materials shows that their applicability depends on the processing conditions and, in a number of cases, ensuring reliable technology lies beyond the characteristics of high- performance tools made from superhard materials. Within the framework of the limitations adopted in the work, the most suitable drills for the conditions of the Ministry of Emergency Situations are those made of hard alloys based on tungsten carbide. These are alloys of the VK6, VK8, VK8M (TC6) series. With a sufficiently high hardness, they have sufficient strength to ensure productive modes of processing such materials as concrete
Доказательный фрагмент
«The share of drilling operations in the total volume of mechanical processing reaches 30...40%.»
Образец извлечения
Демо-превьюThe share of drilling operations in the total volume of mechanical processing reaches 30...40%. Полный текст публикации CiteX не хранит — доступ к первоисточнику открывается по DOI согласно лицензии издателя и выбранному плану.
- Цитирований
- 0
- Просмотров
- 0
- Тип
- Журнал
- Страна
- Узбекистан
- Ключевые слова
- Drilling, carbide drills, operating conditions, deep-hole drills, strength and hardness.
Смежные источники
Академические исследования в современной наукеKhudaiberdiyeva Arafat Israilovna, Ph.D Professor hudayberdiyevaarofat@gmail.com +12026
Общество и инновацииKhosiyat MAMATKULOVA2024
Научные статьиI.B.Yangiboyev, E.X.Berdanov +22025